learn to make money free

paid surveys

Thursday, April 8, 2010

CCNA2 V4.0 Exploration - Chapter 7

Chapter 7 - Exam Answers






1.A network administrator has been told that the company IP address infrastructure must adhere to RFC 1918. What three IP address ranges from RFC 1918 could the administrator use on the network? (Choose three.)

• 10.0.0.0/8
127.0.0.0/8
169.254.0.0/16
• 172.16.0.0/12
• 192.168.0.0/16
209.165.201.0/27



2.Refer to the exhibit. Routers East and West are configured using RIPv1. Both routers are sending updates about their directly connected routes. The East router can ping the West router serial interface and West can ping the serial interface of East. However, neither router has dynamically learned routes from the other. What is most likely the problem?

A gateway of last resort is required.
Subnetting is not supported by RIPv1.
• VLSM is not supported by RIPv1.
One of the routers needs a clock rate on the serial interface.



3.Refer to the exhibit. What effect will the commands that are shown have on RIP updates for Router1?

Only version 2 updates are sent to 255.255.255.255.
• Only version 2 updates are sent to 224.0.0.9.
Both version 1 and version 2 updates are sent to 224.0.0.9.
Both version 1 and version 2 updates are sent to 255.255.255.255.


4.Refer to the exhibit. What can be concluded from the output shown in the exhibit?

The routing table is limited to 2 routes.
The LAN interfaces are participating in the routing process.
One update has been sent out of each serial interface and 2 have been received.
• The no auto-summary has not been configured on this router.

5
What are two reasons to implement RIP version 2 rather than RIP version 1? (Choose two.)

• RIP version 2 supports VLSM.
RIP version 2 supports more than 16 routers.
RIP version 2 supports classful (and not classless) routing
• RIP version 2 supports routing update authentication.
RIP version 2 supports multi-areas.
RIP version 2 uses the Dijkstra algorithm rather than the Bellman-Ford algorithm.


6.Refer to the exhibit. RIPv1 is configured as the routing protocol for the network that is shown. The following commands are used on each router:

router rip
network 10.0.0.0
network 172.16.0.0

When this configuration is complete, users on the LAN of each router are unable to access the remote LANs. Why?

The network statements are configured incorrectly.
A routing loop has been created.
• RIPv1 is unable to route to discontiguous subnets of a major network.
RIPv1 is unable to route networks with a /24 subnet mask.


7.A network administrator installed four new routers that are running RIPv2. Router1 is a boundary router in the RIPv2 network and has a default route configured. Once the network has converged, the network administrator enters Router1(config-router)# default-information originate on Router1. How will this affect the network?

prevents Router1 from forwarding updates about networks that are not directly connected
causes all routers in the network to synchronize routing updates with Router1
forces Router1 to become the primary or designated router (DR) for updates
• propagates the default route to all routers in the network



8.Refer to the exhibit. A technician needs to add a new loopback interface to test routing functionality and network
design. The technician enters the following set of commands on the router:

Sanford(config)# interface loopback1
Sanford(config-if)# ip address 192.168.6.62 255.255.255.252

Why does the router respond with an error?

The router does not allow loopback interface configurations.
This mask can not be used with this class of addresses.
Classless routing must be configured before this address can be added.
• The network address for Loopback1 overlaps with an already configured interface address.
The router is over the limit for the maximum paths that can be provided in the routing table.

9.What is the maximum network diameter permitted by the default metric of RIPv2?

• 15 hops
16 hops
100 hops
120 hops
255 hops


10.What are two functions of the network command used when configuring routing protocols? (Choose two.)

• identifies which networks will be included in the routing updates
identifies the hosts addresses that can be summarized in the network
used to list all addresses for remote and local networks
determines which subnet mask to apply to routing updates
• determines which interfaces can send and receive routing updates


11.Refer to the exhibit. All routers are running RIPv1. What changes will occur in the routing table of router B if a loopback interface with an address of 10.16.1.129/27 is configured on router B?

Routes to the 10.16.1.0/27, 10.16.1.64/27, and 10.16.1.128/27 networks are added.
• A connected route to the 10.16.1.128/27 network is added.
A third route to the 10.0.0.0/8 network with RIPv1 as the source is added.
The 10.0.0.0/8 route is dropped immediately from the routing table after router B is configured.


12.Refer to the exhibit. If all routers are running RIP version 2, why is there no route for the 192.168.1.32/27 network?

Rip version 2 does not send subnet masks in its updates.
Router A is not setup with RIP as a routing protocol.
• Rip version 2 will auto summarize routes by default.
Router B is not setup to advertise the 192.168.1.64/30 network.


13.RIPv2 is the configured routing protocol on the routers in a network. The command Router(config-router)# no version 2 is entered on the routers. What effect does entering this command have on routing updates?

Subnet masks will be added to the routing updates.
Routing updates will be sent out using multicast address 224.0.0.9.
• Version 1 and 2 updates will be received and the version 2 updates will not be sent.
The RIP routing process will be removed from the router and routing updates will not be forwarded.


14.How are RIP v1 and RIP v2 similar to one another? (Choose three.)

• They both use hop count as a metric.
• They both have the same metric value for infinite distance.
They both broadcast their updates to their neighbors.
They both send subnet mask information in their updates.
They both provide for authentication of update sources.
• They both use split horizon to prevent routing loops.


15.Refer to the exhibit. The exhibited network contains a mixture of Cisco and non-Cisco routers. The command debug ip rip was entered on the JAX router. All routers are running the same version of RIP. Router CHI and Router ORL are not able to reach the 192.168.1.16/28 network. What is a possible solution to this problem?

Enable split horizon in the network.
• Configure RIPv2 on routers.
Add network 192.168.1.0 to the RIP configuration on the JAX router.
Configure JAX Fa0/0 as a passive interface.
Enable the Serial0/0/0 interface on the JAX router.
Change the IP address on the Fa0/0 interface of the JAX router to 192.168.1.1/24.


16 .What field was added to the RIP message header by RFC 1723 to add support for VLSM and CIDR?

• subnet mask
destination port number
address family identifier
source and destination IP addresses


17.Refer to the exhibit. Which command on which router will allow Router1 to learn about the 192.168.0.0/20 network?

Router1(config)# ip classless
Router1(config-router)# no passive-interface serial 0/1/1
• Router2(config-router)# version 2
Router2(config-router)# neighbor 10.0.0.2


18.Refer to the exhibit. Which two statements are true? (Choose two.)

• Router1 will install a route to 192.168.0.0/20
Router1 will install a route to 192.168.0.0/24
Router1 will install a route to 192.168.16.0/24
Router2 will install a route to 192.168.16.0/24
• Router2 will not install a route to 192.168.16.0/20



19.Refer to the exhibit. All routers are running RIP version 2. JAX is configured to just advertise the 10.0.0.0/24 network. CHI is configured to advertise the 172.16.0.0/16 network. A network administrator enters the commands shown in the exhibit. What changes will occur in this network?

The JAX router will ignore updates for the 172.16.0.0/16 network due to split horizon issues.
• The CHI router will install a route to the 192.168.0.0/16 network in its routing table.
The routing table for CHI will have the 192.168.0.0/16 route but it will have an S next to the route.
The ORL router will apply a 255.255.0.0 subnet mask to all networks in the routing updates it forwards.



20.Refer to the exhibit. Which command will allow Router2 to learn about the 192.168.16.0/28 network?

Router1(config)# ip classless
• Router1(config-router)# network 192.168.16.0
Router1(config-router)# no passive-interface serial 0/1/1
Router2(config-router)# version 2
Router2(config-router)# neighbor 10.0.0.2

Wednesday, April 7, 2010

CCNA2 V4.0 Exploration - Chapter 6

Chapter 6 - Exam Answers




1. What two advantages does CIDR provide to a network? (Choose two.)

--> reduced routing table size

--> reduced routing update traffic


2. Refer to the exhibit. Which address is a broadcast address for one of the subnets that are shown in the exhibit?

--> 192.168.4.15/29



3. In the network shown in the graphic, three bits were borrowed from the host portion of a Class C address. How many valid host addresses will be unused on the three point-to-point links combined if VLSM is not used?

--> 84


4. Which of the following are contained in the routing updates of classless routing protocols? (Choose two.)

--> 32-bit address

--> Subnet mask



5. Refer to the exhibit. The network administrator wants to create a subnet for the point-to-point connection between the two routers. Which subnetwork mask would provide enough addresses for the point-to-point link with the least number of wasted addresses?

--> 255.255.255.252



6. What does VLSM allow a network administrator to do?

--> utilize multiple subnet masks in the same IP address space



7. Which three interior routing protocols support VLSM? (Choose three.)

--> OSPF

--> RIP v2

--> EIGRP



8. Which of the following problems does VLSM help to alleviate?

--> the shortage of IP addresses



9. Refer to the exhibit. A network technician enters the static route in R1 needed to reach network 10.1.1.0/24. A ping from the S0/0/0 interface on R1 to host B fails. The technician begins testing the network and has the following results:

1. pings from R1 to the S0/0/0 interface on R2....successful

2. pings from R1 to the Fa0/0 interface on R2....successful

3. pings from host B to hosts on the 10.1.1.0/24 network....successful

4. pings from host B to the Fa0/0 interface on R2....successful

5. pings from R2 to host B....successful.

What is the likely cause of the failure of the ping from R1 to host B?

--> The default gateway on host B is not correctly set.




10. A network administrator is tasked with dividing up a class C network among the QA, Sales, and Administration departments. The QA department is made up of 10 people, the Sales is made up of 28 people, and the Administration has 6. Which two subnets masks adequately address the QA and Sales departments? (Choose two.)

--> 255.255.255.224 for Sales

--> 255.255.255.240 for QA



11. Refer to the exhibit. A network engineer is summarizing the two groups of routes on router R1 shown in the exhibit. Which summarization will work for all the subnets?

--> 192.168.0.0/21



12. A Class C address has been assigned for use in the network shown in the graphic. Using VLSM, which bit mask should be used to provide for the number of host addresses required on Router A, while wasting the fewest addresses?

--> /27



13. Refer to the exhibit. In the network that is shown, the router interfaces are assigned the first address in each subnet. Which IP address would be usable for a host on one of the LANs in this network?

--> 192.168.2.130/25



14. Refer to the exhibit. What subnet mask will be applied if Router A sends a RIPv1 update for the network 172.16.1.0 to Router B?

--> 24



15. Refer to the exhibit. The number of required host addresses for each subnet in a network is listed in the exhibit. This number includes the host address requirements for all router ports and hosts on that subnet. After all device and router port address assignments are determined, what will be the total number of unused host addresses available?

--> 29



16. An additional subnet is required for a new Ethernet link between Router1 and Router2 as shown in the diagram. Which of the following subnet addresses can be configured in this network to provide a maximum of 14 useable addresses for this link while wasting the fewest addresses?

--> 192.1.1.224/28



17. What is a supernet?

--> a summarization of classful addresses



18. Refer to the exhibit. A network administrator needs to create two subnetworks from 10.0.0.0/8 for a router running RIPv2. The Admin subnet requires 120 hosts and the Sales subnet requires 58 hosts. The network administrator assigned 10.0.1.128/25 to the Admin subnet. The Sales subnet is given 10.0.1.192/26. What will be the result of this addressing scheme?

--> The subnets overlap and will be rejected by the router.



19. A router has a summary route to network 192.168.32.0/20 installed in its routing table. What range of networks are summarized by this route?

--> 192.168.32.0 – 192.168.47.0/24



20. Refer to the exhibit. The network administrator wants to minimize the number of entries in Router1’s routing table. What should the administrator implement on the network?

--> CIDR

---------------------------------------------------------------------

Tuesday, April 6, 2010

CCNA2 v4.0 Exploration - Chapter 5

Chapter 5 - Exam Answers




1. Refer to the exhibit. The network that is shown is running RIPv1. The 192.168.10.0/24 network was recently added and will only contain end users. What command or set of commands should be entered on Router1 to prevent RIPv1 updates from being sent to the end user devices on the new network while still allowing this new network to be advertised to other routers?

--> Router1(config-router)# no network 192.168.10.0


2. The following line was displayed in the output of the show ip route command.
R 192.168.3.0/24 [120/3] via 192.168.2.2, 00:00:30, Serial0/0
What is the value of the routing metric?

--> 3


3.
Which of the following is considered a limitation of RIP v1?

--> RIP v1 does not send subnet mask information in its updates.


4. Refer to the exhibit. The Ethernet interface on Router2 goes down and the administrator notices that the route is still in the Router1 routing table. How much longer will Router1 keep the down network in its routing table before marking it as possibly down?

--> 155 seconds


5. Refer to the exhibit. Router1 is running RIPv1. What command was entered into Router1 to configure the gateway of last resort?

--> ip route 0.0.0.0 0.0.0.0 S0/0/1


6. What are three characteristics of the RIPv1 routing protocol? (Choose three.)

--> uses hop count as a metric
--> considers a metric of 16 as infinity
--> calculates metrics using the Bellman Ford algorithm


7. Which of the following would be the correct command sequence to enable RIP on Router B for all connected networks?


RouterB(config)# router rip
RouterB(config-router)# network 198.16.4.0
RouterB(config-router)# network 210.36.7.0
RouterB(config-router)# network 220.17.29.0


8. What is the default update period in seconds for the RIP routing protocol?

--> 30




9. Refer to the exhibit. What can be concluded from the routing table output of router B?

--> The default-information originate command has been entered on A.



10. Refer to the exhibit. A network consists of multiple routers. What can be verified when the show ip protocols command is issued on one of the routers in the network?

--> routing protocol configuration in use for IP on this router



11. Refer to the exhibit. All routers are configured with valid interface addresses in the indicated networks and are running RIPv1. The network is converged. Which routes are present in the routing tables?

--> All routers have all /30 routes. Routers A and E also have some of the /24 routes in their routing table.



12. Which two statements are true regarding the characteristics of RIPv1? (Choose two).

--> It is a distance vector routing protocol.

--> The data portion of a RIP message is encapsulated into a UDP segment.



13. Which command or set of commands will stop the RIP routing process?

--> RouterB(config)# no router rip



14. Refer to the exhibit. All routers in the exhibit are running RIP v1. The network administrator issues the show ip route command on router A. What routes would appear in the routing table output if the network is converged? (Choose two).

--> R 192.168.2.0/24 [120/1]

--> R 10.10.1.0/24 [120/2]



15. Which command will display RIP activity as it occurs on a router?

--> debug ip rip



16. Refer to the output from the show ip route command. What can be concluded from the output of this router command?

--> There are two equal cost paths to network 1.0.0.0.



17. Refer to the exhibit. Router1 and Router2 are running the RIPv1 protocol. The network administrator configures the command network 10.1.0.0 on Router1. What network will Router1 advertise to Router2?

--> 10.0.0.0/8



18. Refer to the exhibit. Pings between the serial interfaces of the routers are successful. Hosts on each LAN can ping the Fa0/0 interface of the router to which they are directly connected through the switch. However, pings between hosts on the 10.1.1.0/24 and 10.1.2.0/24 networks are unsuccessful. What is a likely cause of this problem?

--> RIP is configured incorrectly on R1.



19. What will happen if an interface IP address is entered for the address portion of the network command in a RIPv1 configuration instead of a network address?

--> All interfaces in the same classful network as the configured address will be included in the RIPv1 routing process.


20. Refer to the exhibit. All routers that are shown are running the RIP routing protocol. All unknown IP traffic must be forwarded to the ISP. What router or set of routers are recommended to have both a default route and the default-information originate command issued to implement this forwarding policy?

--> only the gateway router


Monday, April 5, 2010

CCNA2 V4.0 Exploration - Chapter 4

 Chapter 4 - Exam Answers





1. Which event will cause a triggered update?
--> a route is installed in the routing table


2. Three routers running a distance-vector routing protocol lost all power, including the battery backups. When the routers reload, what will happen?
--> They will send updates that include only directly connected routes to their directly connected neighbors.


3. What does the RIP holddown timer do?
--> instructs routers to ignore updates, for a specified time or event, about possible inaccessible routes


4. Which two statements are true regarding the function of the RIPv1 routing updates? (Choose two).
--> updates are broadcast at regular intervals
--> broadcasts are sent to 255.255.255.255


5. Which of the following statements are correct about RIP?
--> will send out an update if there is a failure of a link


6. Which two statements describe EIGRP? (Choose two.)
--> EIGRP sends triggered updates whenever there is a change in topology that influences the routing information.
--> EIGRP sends a partial routing table update, which includes just routes that have been changed.


7. Which statement is true regarding cisco’s RIP_JITTER variable?
--> It prevents the synchronization of routing updates by subtracting a random length of time ranging from 0% to 15% of the specified interval time from the next routing update interval.


8. What actions will occur after RouterA loses connectivity to network 114.125.16.0? (Choose two.)
--> RouterB will include network 123.92.76.0 and 136.125.85.0 in its update to RouterA.
--> Router C will learn of the loss of connectivity to network 114.125.16.0 from RouterB.


9. Which of the following methods does split horizon use to reduce incorrect routing information?
--> Information learned from one source is not distributed back to that source.


10. The graphic shows a network that is configured to use RIP routing protocol. Router2 detects that the link to Router1 has gone down. It then advertises the network for this link with a hop count metric of 16. Which routing loop prevention mechanism is in effect?
--> route poisoning


11. What is the purpose of the TTL field in the IP header?
--> limits the time or hops that a packet can traverse through the network before it should be discarded


12. Which of the following can exist in a distance vector network that has not converged? (Choose three.)
--> routing loops
--> inconsistent traffic forwarding
--> inconsistent routing table entries


13. Refer to the exhibit. The routers in this network are running RIP. Router A has not received an update from Router B in over three minutes. How will Router A respond?
--> The Invalid timer will mark the route as unusable if an update has not been received in 180 seconds.


14. A network administrator is evaluating RIP versus EIGRP for a new network. The network will be sensitive to congestion and must respond quickly to topology changes. What are two good reasons to choose EIGRP instead of RIP in this case? (Choose two.)
--> EIGRP only updates affected neighbors.
--> EIGRP updates are partial.


15. Refer to the exhibit. What path will packets from the 192.168.1.0/24 network travel to reach the 10.0.0.0/8 network if RIP is the active routing protocol?
--> The path will be router A -> router D -> router E.


16. Which three routing protocols are distance vector routing protocols? (Choose three).
--> RIPv1
--> EIGRP
--> RIPv2


17. What is a routing loop?
--> a condition where a packet is constantly transmitted within a series of routers without ever reaching its intended destination


18. Which two conditions are most likely to cause a routing loop? (Choose two.)
--> inconsistent routing tables
--> incorrectly configured static routes


19. What metric does the RIP routing protocol consider to be infinity?
--> 16


20. What does a router running RIP do first with a new route that is received from an advertisement?
--> adjusts the metric for the new route to show the added distance for the route


21. Refer to the exhibit. If all routers are using RIP, how many rounds of updates will occur before all routers know all networks?
--> 3